5.0 Robotics Executive CNC Routers - Specifications
These are the technical specifications of our 5.0 Robotics Executive CNC Routers (Model 8, Model 16, and Model 32). They cover:
X, Y, and Z travel with closed loop AC servo on all drive systems
Spindle systems made in Italy
Motion system
Technical data
Machine accuracy
Machine gantry
X, Y and Z travel and stepper motors (AC servo As Standard)
Model 8
Model 16
Model 32
X axis travel
610mm (24 inches) 400W AC servos.
1220mm (48 inches) 400W AC servos
1220mm (48 inches) 400W AC servos
Y axis travel
1220mm (48 inches) 400W AC servos
1220mm (48 inches) 400W AC servos
2440mm (96 inches) 400W AC servos
Z axis travel
200mm (7.87") 400W AC servos
Table work area*
The machine cutter centre to cutter travel is 620mm x 1230mm within this Table
The machine cutter centre to cutter travel is 1230mm x 1230mm within this Table
The machine cutter centre to cutter travel is 2460mm x 1230mm within this Table
* Table work area is not the same as the machine travel this is the Tslot table size on the machine.
Spindle systems made in Italy
These specifications are for Model 8, Model 16 and Model 32.
2.2kW MTC Spindle
Manually change spindle system - 2.2KW ER25 collet Tekno air-cooled spindle with ER25 collet system. 24,000RPM Max cutter size 16mm shank
2.2 kW QTC Spindle
Quick change spindle system - 2.2kW Spindle with HSK32 ER20 manually changed tool holder. Tool change is carried out with a torqued Allen key wrench. The advantage is tool changes without the cost and complexity of full robotic automatic tool change. Max cutter size 13mm shank
2.2 kW QTC Spindle
2.2kW 30,000 RPM spindle system with fully automatic air drive pick and place ATC automatic tool change. NOTE this spec requires closed loop AC servos (is not supplied on any machine with stepper motors) and required a tool magazine to manage the tools for the automate changing. ER20 ISO20 tooling – Max cutter size 13mm shank.
RPM
All 2.2kW spindle are supported up to 24,000 RPM and the ATC spindle can realise 30,000 RPM.
Model 32 ATC
Special note on model 32: Model 32 can be supplied on a 4kW ISO30 ATC system. The spindle runs ISO30 tooling with an ER32 collet system.
Motion system
Model 8
Model 16
Model 32
Full Ballscrew system
T7 GRADE
20mm Ballscrew on X andY Axes
16mm Ballscrew on Z Axis
Two 20mm Ballscrews on Y Axis
One 20mm Ballscrew on X Axis
One 16mm Ballscrew on Z Axis
Two 25mm Ballscrews on Y Axis
20mm ballscrew on X
16mm ballscrew on Z
50μm pitch error over 300mm and typical repeatability of 20um.
NOTE - 400W AC Servo Models will run 20mm ball screws on X and Y Axes.
Precision Linear Rails
The machines run on 20mm size profiled linear HIWIN rails with 4 carriages per axis for maximum strength and rigidity and no compromise!
Technical data
Model 8
Model 16
Model 32
Machine base
All steel frame - 10mm steel laser cut - 80 x 40 steel box section with 5mm wall thickness. Precision machined on aerospace machining center before rail and ball screw end condition assembly
Model 32 main frame is based on 80mm x 100mm steel tubes with 5mm wall. End plates 10mm laser cut steel
Floor space requirement
1350 x 2250mm with safety cover
2250 x 2250mm with safety cover
3500 x 2500mm
Weight
300 kg*
500 kg*
1000 kg*
*depends on extra and configuration
Power
230v 1phase - main machine will run off a 13A single phase supply. The vacuum pump supply will be separate if applied to the machine
Can be supplied single phase powered. The 4kW ATC version requires 3 phase
Machine accuracy
These specifications are for Model 8, Model 16 and Model 32.
Machine accuracy
Straight to <0.05mm over 1000mm of stroke.
Square to < 0.05 between XY and XY plane and Z.
Repeatability <0.02mm
Rapid Feed Rate
10,000mm/min - 30,000mm/min (depends on model and drive system [stepper vs servo])
​We perform a geometric accuracy test on each machine we produce
All of our measurements are made with Mitutoyo-calibrated instruments
Machine gantry
These specifications are for Model 8, Model 16 and Model 32.
Gantry bridge
160x80mm heavy-duty Alloy Bridge. For light and strong construction. High accelerations and speeds realized and high strength for maximum rigidity.
Gantry Supports
FEA designed precision machined construction - the Gantry supports are machined from solid 6082T6 Alloy on a machining centre and have been optimized for max strength transfer into the bridge from the frame.
Gantry Clearance
A standard 170mm clearance and repositionable Z height allow for an extension to 200mm clearance.
The Z axis has a 200mm stroke - so the spindle is moved fully up and out of the clearance zone.